an oil filter and a diesel filter, commonly known as "three filters". "we are oil filter wholesale and best oil filter china,you can know it.
Filter maintenance points
The engine of the tractor and the agricultural transport vehicle is equipped with an air filter, an oil filter and a diesel filter, commonly known as "three filters". "we are oil filter wholesale and best oil filter china,you can know it.
The operation of the "three filters" directly affects the working performance and service life of the engine. At present, there are quite a few drivers who do not follow the time and regulations required in the manual to carry out the
maintenance and maintenance of the "three filters", resulting in frequent engine failures. , enter the maintenance period too early.
1. Air filter maintenance points. In addition to careful maintenance of the air filter according to the specified time and operating requirements of the instruction manual, the following should be noted:
(1)The air guide grille of the air filter should be kept free from deformation and rust, and its inclination angle should be 30 to 45°. If it is too small, the resistance will increase, affecting the intake air. If it is too large,
the airflow will be weakened and the dust will be separated. The ability is reduced. The surface of the blade must not be painted to prevent oxidation particles from entering the cylinder. The direction of the dust outlet should be
based on the ability to discharge dust particles.
(2)The ventilation mesh should be cleaned during maintenance; for dust cups, the dust particles should not exceed 1/3 of the height, otherwise it should be removed in time; the dust cup mouth seal should be tight, and the rubber seal
should not be damaged or lost. .
(3)The oil level of the fine filter should be compliant with the standard. If it is too high, the oil will enter the cylinder and deposit carbon. If it is too low, the filtration will be reduced and the wear will be accelerated.
(4)For the metal mesh (wire) used in the fine filter, the diameter of the hole or wire can only be slightly smaller, can not be increased, and the filling amount should not be reduced, otherwise the filtration effect will be reduced.
(5)There should be no air leakage in the intake pipe. The oil change and cleaning should be carried out in the place where there is no wind and no dust; the blowing filter should be used with high pressure air in the environment with
low humidity, and the direction of blowing should enter the filter with air. The direction is reversed; when installed, the adjacent filter creases should intersect each other.
2.Oil filter maintenance points. The oil filter must be maintained for the specified time, and pay attention to the following points:
Centrifugal oil filter, maintenance of centrifugal fine filter should pay special attention to the installation after disassembly:
1There should be no blocking phenomenon. The inspection method is: after the rotor is installed, the rotor is rotated by hand, and after the hand is released, the rotor can be freely turned 2-3 turns and then stopped, which is qualified;
2It is also possible to install the fine filter on the vehicle, start the engine, run for a few minutes at the rated speed, and turn off when the oil temperature reaches 70 °C. At this time, the rotor is still rotating outside the casing and can continue to rotate for more than 1.5 minutes. Qualified for installation. If the above indicators are not met, the installation is unqualified and should be reassembled.
Product Name: Oil Fiter
Brand Name: RSD
Warranty: 1 Years
Car Model: BMW
OE NO.: 11427566327
Material: Filter Paper
Application: Engine Parts
Package: Neutral Packing
Q1: What's the MOQ?
A:1. Oil filter with metal: MOQ=2000pcs
2.Oil filter without metal: MOQ=2000pcs
3. Air filter: MOQ=2000pcs
4. Cabin filter: MOQ=2000pcs
Q2. What is your terms of packing?
A: Generally, we pack our goods in neutral white boxes and brown cartons. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.
Q3. What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages before you pay the balance.
Q4. What is your terms of delivery?
A: EXW, FOB, CFR, CIF, DDU.
Q5. How about your delivery time?
A: Generally, it will take 15-30days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.
Q6. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q7. What is your sample policy?
A: We can supply the sample if we have ready parts in stock, but the customers have to pay the courier cost.
Q8. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery
Q9. What’s our shipping ways?
A: By sea, air, land.
Q10: How do you make our business long-term and good relationship?
A:1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.